TiWi-uB1 Bluetooth Module

Not Recommended for New Design (NRND)

Overview

The TiWi-uB1 Bluetooth Smart module is a low-power 2.4 GHz Bluetooth 4.0 (Bluetooth Low Energy) System-on-Chip in a cost effective, pre-certified footprint. This module comes ships with no firmware in the embedded flash. Applications can be developed and loaded into the integrated microcontroller and function without the need for an external processor.

Features:

  • Bluetooth Smart (Bluetooth Low Energy v4.0)
  • RF Output Power: 0 dBm (Class 3)
  • Certified with on module PCB trace and off module dipole antennas
  • Compact design based on Texas Instruments CC2541 Transceiver (256 KB, 8 KB RAM)
  • Multiple configuration options 
    - Network processor interface for applications running on an external microcontroller
    - Single-Chip configuration, allowing applications running on internal microcontroller
  • Low power operation
  • RoHS compliant

Specifications

Chipset
TI CC2541
Processor On Board
8051 Microcontroller
Operating Temp (Min) (°C)
-40
Antenna Options
Integrated or External via Trace Pad
BT Capable
Complete Power-Optimized Stack
Controller and Host
GAP - Central, Peripheral, Observer, or Broadcaster
ATT / GATT - Client and Server
SMP - AES - 128 Encryption and Decryption
L2CAP
Bluetooth Version
Bluetooth 4.0 (Bluetooth LE)
Certifications
FCC, ISED, EU, UKCA, MIC, Bluetooth SIG
Dimension (Height - mm)
11.6 mm
Dimension (Length - mm)
17.9 mm
Dimension (Width - mm)
2.3 mm
Interfaces - General
UART, SPI, Digital I/O, and Analog Inputs
Operating Temp (Max) (°C)
+85 °C
Receive Sensitivity
-94 dBm (1 mpbs)
Transmit Current
21.1 mA, Transmit (0 dBm, no peripherals active, low mcu activity)
25.7 mA, Receive (standard mode, no peripherals active, low mcu activity)
Transmit Power
0 dBm
Part NumberAntenna OptionsAntenna TypeBulk or SingleChipset (Wireless)Frequency Range (Max)Frequency Range (Min)Logical InterfacesOS/SoftwareProduct TypeSystem ArchitectureTechnologyType
450-0103C
End of Life (EOL)
Buy Now
PCB Trace Antenna External Bulk, Cut Tape TI CC2541 2480 MHz2402 MHzSerial, SPI, DIO, Analog HCI Embedded Module Hostless Bluetooth 4.0, Single Mode (BLE) Module
450-0103R
End of Life (EOL)
Buy Now
PCB Trace Antenna External Bulk, Tape and Reel TI CC2541 2480 MHz2402 MHzSerial, SPI, DIO, Analog HCI Embedded Module Hostless Bluetooth 4.0, Single Mode (BLE) Module
450-0106C
End of Life (EOL)
Buy Now
External Antenna Port External Bulk, Cut Tape TI CC2541 2480 MHz2402 MHzSerial, SPI, DIO, Analog HCI Embedded Module Hostless Bluetooth 4.0, Single Mode (BLE) Module
450-0106R
End of Life (EOL)
Buy Now
External Antenna Port External Bulk, Tape and Reel TI CC2541 2480 MHz2402 MHzSerial, SPI, DIO, Analog HCI Embedded Module Hostless Bluetooth 4.0, Single Mode (BLE) Module

Development Kits

  • 450-0120

    450-0120

    Antenna Type
    External
    Logical Interfaces
    Serial, SPI, DIO, Analog
    Learn More

Documentation

Name Part Type Last Updated
Datasheet - TiWi-uB1 All Datasheet 01/17/2019
Antenna Design Guide - TiWi-uB1 All Documentation 01/17/2019
Product Brief - TiWi-uB1 All Product Brief 10/12/2021
3D Models - TiWi-uB1 All Technical Drawings 01/17/2019
SCH and PCB Models- TiWi-uB1 All Technical Drawings 01/17/2019
EM Board User Guide - TiWi-uB1 All Documentation 01/17/2019
EM Board CAD - TiWi-uB1 All Technical Drawings 01/17/2019
Bluetooth SIG Listing - TiWi-uB1 All Certification 01/17/2019
Conflict Minerals Statement All Documentation 01/17/2019
RoHS Statement - LSR All Certification 01/17/2019
FCC and ISED (Canada) Certifications - TiWi-uB1 All Certification 12/19/2020
EU Certifications - TiWi-uB1 All Certification 06/02/2021
Product Life Cycle Policy - TiWi-uB1 All Certification 01/17/2019
REACH - TiWi-uB1 All Certification 01/17/2019
RoHS Test Report - TiWi-uB1 All Certification 01/17/2019
WEEE Statement - TiWi-uB1 All Certification 01/17/2019
NCC Certifications - TiWi-uB1 All Certification 12/19/2020
TiWI-uB1 EMLink Source Code - Android All Software 01/17/2019
TiWI-uB1 EMLink Source Code - iOS All Software 01/17/2019
Bluetooth Eval Tool All Software 01/17/2019
Host Test App All Software 01/17/2019
TiWI-uB1 EM Board Hex File All Software 01/17/2019
WLAN and Bluetooth Radio Tools User Guide All Documentation 05/01/2019
Android App Source Files All Software 03/29/2019
Bluetooth Eval Tool All Software 03/29/2019
Host Test App All Software 03/29/2019
iOS App Source Files All Software 03/29/2019
TiWi-uB1 EM Board Hex File All Software 03/29/2019
WLAN and Bluetooth Radio Tools User Guide All Software 05/01/2019
Xamarin ModuleLink Source Code All Software 04/02/2020
Regulatory Information - TiWi-uB1 All Certification 03/17/2023
PCN 12D-2021 - TiWi-uB1 All Documentation 01/04/2022
EOL Notice - TiWi-uB1 and TiWi-uB2 - Oct 2023 All Documentation 11/13/2023

FAQ

Can I use the module with an external host microcontroller?

Yes, the module can be used with an external host. Ezurio (formerly Laird Connectivity) does not provide any out-of-the-box firmware for the module that will allow this mode of operation. There are some great starter examples provided by TI here: Using the CC254x with an external host

Can I use the TiWi-uB1 module in Network Processor mode?

The TiWi-uB1 module can be used in conjunction with an external host processor or microcontroller, using the HCI command protocol over a UART or SPI interface.

Which antennas are certified with the TiWi-uB1 module?

The TiWi-uB1 module is certified with an on module PCB trace antenna. Additionally the module is also certified with the Ezurio 2.4 GHz Dipole and 2.4 GHz Waterproof Dipole antennas, used in conjunction with any of our U.FL to Reverse Polarity SMA cables. Note that the correct model of module needs to be ordered based on the antenna option being used (PCB Trace: 450-0103, Off Module: 450-0106). Consult the Antenna Design Guide for details on implementing the TiWi-uB1 module into your design with one of the above certified antenna options.

Is the TiWi-uB1 module a single mode or dual mode device?

The TiWi-uB1 is a single mode Bluetooth Smart module, that supports Bluetooth Low Energy (BLE) only.

Can I develop my application directly on the TiWi-uB1 module?

The TiWi-uB1 module is a System-On-Chip (SOC), that has an integrated microcontroller that can be used for application development.

Do I need to use a 32,768 Hz crystal with the TiWi-uB1 module?

A 32 kHz crystal is required in applications that use power savings, to maintain the connection timing required by BLE. If your application is line powered and does not use power savings, the timing is maintained by the 32 MHz crystal, and hence no 32 kHz crystal is required.

What is the recommendation for washing BT/BLE modules?

We recommend using de-ionized water. Additionally, we recommend avoiding any sonic vibration, heat, and pressure washing as well as any other soaps/chemicals.

Can I use the Manufacturer's Specific AD record Data Type for Proprietary Data?

The Manufacturer's Specific Data Type is used for manufacturer specific data which can be proprietary data structures defined by the manufacturer and only identifiable by manufacturer's equipment/applications. To use the Manufacturer's Specific Data Type you need to have a Company Identifier as assigned by the BT SIG. You must be a registered member of the BT SIG and must apply for the company identifier using the process below (found at this link: https://www.bluetooth.com/specifications/assigned-numbers/company-ident…)   Application & Assignment Process Submit the following below to  Bluetooth Support : Company information (legal name of company) Name of company's primary contact (name and email) A statement that your company is currently a Bluetooth SIG member in good standing* Please allow five business days for your request to be fulfilled, and two business days from the time your request is fulfilled to view your Company Identifier on this page. *  ? BLUETOOTH Member in Good Standing ? shall mean any firm, corporation or other legal entity that has been admitted to membership in the BLUETOOTH SIG, whether a Promoter Member, Associate Member or Adopter Member, as defined in the organizational documents, that has fulfilled all of the requirements for membership, has paid and is current with payment of any and all membership fees, dues and assessments, and whose membership neither has been voluntarily or involuntarily suspended, terminated, or withdrawn from membership consistent with the lawful provisions of the organizational documents of the BLUETOOTH SIG.?

How can I test WLAN on the TiWi Series?

The TiWi-BLE can be tested a couple of ways. Either with the TiWi WLAN Eval Tool or in Linux with the following weblink to guide on how to do that. The customer needs to read through our product documentation before going to the following Ti page: http://processors.wiki.ti.com/index.php/WL127x_TX_Testing

Before we suggest using the Ti link above, the module must be calibrated, those steps and instructions are in the Documentation section on the product page.

 

 

What is the difference between TiWi-uB1 revisions?

The difference between the two revisions (R1 and R2) is the label change located on the module itself. The hardware is exactly the same and will run the same firmware on both revisions.

What criteria should be confirmed when soldering Bluetooth modules?

The factors to confirm when checking the soldering job on Bluetooth modules are solder stencil aperture size, solder stencil thickness, solder ball size, solder type, and the MSL guidelines. If the parts have been left out for too long then the modules should be baked to remove any moisture prior to soldering. If there are any failures, we highly recommend providing an x-ray of the module.

Does Ezurio provide 3D files for modules?

Ezurio provides 3D files (STEP) files for most but not all of it's modules.  Based on the nature of the information in the files, in most cases Laird requires a login to access these files as well as layout files and software/firmware downloads.  As such, for most modules, the 3D files are found under the Software Downloads tab of the product page.  The page offers a credentials request link for customers who need credentials.  In most cases, the credentials are provided via return email within about 10 minutes. Please contact support if you have any additional questions or have any issues accessing our downloads.

Do we recommend conformal coating your modules?

We highly do not recommend conformal coating the radio module. If you plan on encapsulating the radio module in a potting compound or conformal coating, you must assure that the compound in liquid or solid form does not enter under the shield where there are sensitive RF components. Some of the capacitive and inductance values are as low (pF and nH) and could be sensitive to contacting materials such as potting compounds. There are potting compounds and conformal coatings which have very good dielectric constants and are suitable for 2.4 GHz potting applications, however, when you apply any of these, they were not accounted for in the circuit design and might reduce performance of the device (or all together cause it not to function).  You should run tests on their particular potting compound and evaluate radio's performance and range.  Also, it's worth mentioning that applying any compound, conformal coating or potting directly to the module WILL void the warranty. If your application requires 100% sealing of the radio module, there is a way to do this very successfully without impacting the module performance. Simply place the module on your PCB. Place a plastic cover over the module (like a hat), make the cover large enough to cover the whole module. Apply glue around the bottom perimeter of the cover where it sits on the PCB. This allows the module to function in free air-space while there is a complete seal around it. This information is only for reference and we recommend you should conduct your own testing with your prototype of your end application to find the best suitable fit for your design.  

How many reflows do you recommend for your modules?

We only recommend reflowing our modules once as it can damage the module and void the warranty.

Where is the HostTestApp source code for the TiWi-uB1?

The HostTestApp is an example included in the TI BLE Stack. It can be located at the link below. http://www.ti.com/tool/ble-stack Below is an app note that should help in the process as well. http://processors.wiki.ti.com/index.php/PTM_cc2640

What are the available CAD file formats?

Ezurio provides layout files PADS and PADS ASCII formats. The ASCII files will import to Altium (and Protel varients) as well as Cadence (Orcad and Allegro) CAD packages. As far as we know, there is no way to import to Eagle CAD. Please be sure to use the .asc file for PCB and the .txt file for the schematic when importing to Altium. Ezurio uses ORCAD for schematics (Gerbers). 

What's the recommended process to clean modules?

The recommended cleanser is "hydrocarbon cleaning oil", which can be used to clean the RF shield and PCB. We do not recommend the use of alcohol as it doesn't work as well and could leave residue on the boards.  

Become a Ezurio Customer and Gain Exclusive Access to Our Design Services Team

  • Antenna Scans
  • Antenna selection and placement
  • Custom antenna design
  • Worldwide EMC testing / certifications
  • Embedded RF hardware / firmware design
  • Cloud architecture and integration
  • Mobile application development
  • Product & Industrial Design

Talk to an Expert

Buy Now

Distributor Part In Stock Region Buy
Avnet 450-0103C 0 North America Buy Now
DigiKey 450-0103C 0 North America Buy Now
Symmetry Electronics 450-0103C 0 North America Buy Now
DigiKey 450-0103R 695 North America Buy Now
DigiKey 450-0103R 695 North America Buy Now
Avnet 450-0103R 0 North America Buy Now
DigiKey 450-0103R 0 North America Buy Now
Symmetry Electronics 450-0103R 0 North America Buy Now
DigiKey 450-0106C 909 North America Buy Now
Avnet 450-0106C 0 North America Buy Now
Symmetry Electronics 450-0106C 0 North America Buy Now
Avnet 450-0106R 0 North America Buy Now
DigiKey 450-0106R 0 North America Buy Now
Symmetry Electronics 450-0106R 0 North America Buy Now
Avnet 450-0120 0 North America Buy Now
DigiKey 450-0120 0 North America Buy Now
Symmetry Electronics 450-0120 0 North America Buy Now

Distributors

Distributor Phone Number Region Website
Alpha Micro UK Only +44 1256-851770
EMEA Website
Arrow Electronics 1-855-326-4757
+44 2039 365486
APAC, North America, South America, EMEA Website
Avnet 1-480-643-2000
+44 1628 512900
APAC, North America, South America, EMEA Website
Braemac Australia, New Zealand, South East Asia +61 2 9550 6600
+64 9 477 2148
APAC Website
Cal-Chip Connect 1-215-942-8900
North America Website
DigiKey 1-800-344-4539
North America, South America, APAC, EMEA Website
EBV Elektronik EMEA Website
Farlink Technology China, Hong Kong +86 13266922199
APAC Website
Farnell 1-800-936-198
+44 3447 11 11 22
EMEA Website
Future Electronics 1-800-675-1619
1-514-428-8470
North America, South America, APAC, EMEA Website
Glyn +49-6126-590-0
EMEA Website
Jetronic China, Hong Kong and Taiwan 852-27636806 
APAC Website
Laird Connectivity 1-847-839-6925
+44 1628 858941
North America, South America, APAC, EMEA Website
M2M Germany +49-6081-587386-0
EMEA Website
Martinsson +46 8 7440300
EMEA Website
McCoy South East Asia +65 6515 2988
APAC Website
Mouser 1-800-346-6873
+44 1494 427500
North America, South America, APAC, EMEA Website
RS Components +852-2421-9898
+44 3457-201201
North America, South America, APAC, EMEA Website
Ryoyo Japan +81-3-3543-7711
APAC Website
Solsta UK Only +44 (0) 1527 830800
EMEA Website
Supreme Components International India, South East Asia +65 6848-1178
APAC Website
Symmetry Electronics 1-866-506-8829
North America Website
Tekdis Australia and New Zealand +61 3 8669 1210
APAC Website
Telsys +972 3 7657666
EMEA Website
WPG +44 1628 958460
EMEA Website