Overview

The SDC-CF10G provides all key Summit brand hardware and software capabilities in a compact flash form factor. As a result, the SDC-CF10G is ideal for integration into application specific devices like portable data terminals, portable printers and medical devices. Hardware innovations enable the SDC-CF10G module to provide far greater performace and range than WLAN radio modules designed for office and consumer applications while minimizing power consumption and allowing for operation in challenging environments.

Note: This product has reached end of production and is available on a limited basis only.

Specifications

Certifications
Wi-Fi Alliance: 802.11b, 802.11g. WPA Enterprise, WPA2 Enterprise. Cisco Compatible Extensions (Version 4).
Chipset (Wireless)
Broadcom BCM4318E
Compliance
FCC, ISED, EU, MIC
Connector Type
Compact Flash
Dimension (Height - mm)
3.3 mm
Dimension (Length - mm)
54.5 mm
Dimension (Width - mm)
43 mm
Input Power
Requirements 3.3 VDC +/- 10%
Mounting
50 pin connector, Through Hole
Network Architecture
Infrastructure and Ad Hoc
Operating Channels (2.4 GHz)
ETSI:13 (3 non-overlapping) FCC:11 (3 non-overlapping) MIC:14 (4 non-overlapping)
Operating Humidity
10 to 90% (non-condensing)
Operating Systems Supported
Windows Mobile, CE, XP Professional, XP Embedded
Power Consumption
Transmit:440 mA (1320mW). Receive:180 mA (594mW). Standby:10 mA (33 mW).
Protocols
Media Access: Carrier sense multiple access with collision avoidance (CSMA/CA)
Security
Standards: Wireless Equivalent Privacy (WEP), Wi-Fi Protected Access (WPA), IEEE 802.11i (WPA2). Encryption: Wireless Equivalent Privacy (WEP, RC4 Algorithm), Temporal Key Integrity Protocol (TKIP, RC4 Algorithm), Advanced Encryption Standard (AES, Rijndael Algorithm). Encryption Key Provisioning: Static (40 and 128 bit lengths). Pre-Shared (PSK)Dynamic: 802.1X Extensible Authentication Protocol. Types: EAP-FAST, EAP-TLS, EAP-TTLS, PEAP-GTC, PEAP-MSCHAPv2, PEAP-TLS, LEAP
Transmit Power (Max)
N/A
Weight
.529 oz (15 g)
Wireless Specification
Bluetooth Version 4.0 BLE
Part NumberAntenna OptionsAntenna TypeChipset (Wireless)ComplianceConnectorDimension (Height - mm)Dimension (Length - mm)Dimension (Width - mm)Frequency Range (Max)Frequency Range (Min)Input PowerLogical InterfacesNetwork ArchitectureOS/SoftwareOperating Channels (2.4 GHz)Operating HumidityOperating Systems SupportedPower ConsumptionPower Consumption (Rx)Power Consumption (Tx)Product TypeProtocolsSecuritySystem ArchitectureTechnologyWeightWireless Specification
SDC-CF10G
End of Life (EOL)
Buy Now
u.FL Connector (x2) External Broadcom BCM4318E ETSI Compact Flash 3.3 mm54.5 mm43 mm2480 MHz2402 MHz3.3 VDC +/- 10% Compact Flash Infrastructure and Ad Hoc Windows XP, Windows Embedded, Windows Mobile, Windows CE ETSI:13 (3 non-overlapping) FCC:11 (3 non-overlapping) MIC:14 (4 non-overlapping) 10 to 90% (non-condensing) Windows Mobile Transmit: 440 mA (1320mW). Receive:180 mA (594mW). Standby:10 mA (33 mW). 180 mA 440 mA Embedded Module Media Access: Carrier sense multiple access with collision avoidance (CSMA/CA) Standards: Wireless Equivalent Privacy (WEP) Hosted 802.11bg .529 oz (15 g) 802.11 b/g Wi-Fi

Documentation

Name Part Type Last Updated
EN 300 328 - CF10G.pdf All Certification 01/17/2019
EN 301 489 - CF10G.pdf All Certification 01/17/2019
EN 50371 - CF10G.pdf All Certification 01/17/2019
EN 60950-1 - CF10G.pdf All Certification 01/17/2019
EN 62311 - CF10G.pdf All Certification 01/17/2019
EU Standards Updates.pdf All Certification 01/17/2019
FCC 15B Test Report - CF10G.pdf All Certification 01/17/2019
FCC 15C Grant - CF10G.pdf All Certification 01/17/2019
FCC 15C Test Report (C2PC) - CF10G.pdf All Certification 01/17/2019
FCC 15C Test Report - CF10G.pdf All Certification 01/17/2019
FCC C2PC - CF10G.pdf All Certification 01/17/2019
FCC DFS Test Report - CF10AG.pdf All Certification 01/17/2019
FCC DTS Grant - CF10G.pdf All Certification 01/17/2019
FCC DTS Test Report - CF10AG.pdf All Certification 01/17/2019
FCC RF Exp Report - CF10G.pdf All Certification 01/17/2019
IC - 6616A Certificate - CF10G.pdf All Certification 01/17/2019
IC - Test Report - CF10G.pdf All Certification 01/17/2019
MIC - GZ (Channel 14) - CF10G.pdf All Certification 01/17/2019
MIC - GZ Test Report - CF10G.pdf All Certification 01/17/2019
MIC - WW (Channel 1-13) - CF10G.pdf All Certification 01/17/2019
MIC - WW Test Report - CF10G.pdf All Certification 01/17/2019
MIC-GZ - CF10G.pdf All Certification 01/17/2019
MIC-WW - CF10G.pdf All Certification 01/17/2019
RF Exp TWG-SDCCF10G.pdf All Certification 01/17/2019
RM941208L11.pdf All Certification 01/17/2019
RM941208L11B.pdf All Certification 01/17/2019
SDC-CF10G FCC 0404.pdf All Certification 01/17/2019
TestRpt-FCC 15B SDC-CF10G.pdf All Certification 01/17/2019
Test Rpt TWG-SDCCF10G.pdf All Certification 01/17/2019
Test report-Chennel 14.pdf All Certification 01/17/2019
WCFB-105G CE 0614-1.pdf All Certification 01/17/2019
WCFB-105G CE 0614-2.pdf All Certification 01/17/2019
WCFB-105G CE 0614-3.pdf All Certification 01/17/2019
WCFB-105G CE 0614-4.pdf All Certification 01/17/2019
WCFB-105G FCC and CE data.pdf All Certification 01/17/2019
RoHS 3 Compliance - Wi-Fi Products All Certification 01/11/2024
End of Life Announcement - CF10G.pdf All Documentation 01/17/2019
Frequently Asked Questions - Wi-Fi Software Developers Kit.pdf All Documentation 01/17/2019
Hardware Integration Guide - CF10G.pdf All Documentation 01/17/2019
Quick Start Guide - Wi-Fi on Windows XP.pdf All Documentation 01/17/2019
User Guide - Summit Software Developers Kit.pdf All Documentation 01/17/2019
Usage Notes - Laird Wi-Fi Software.pdf All Documentation 01/17/2019
Quick Start Guide - Wi-Fi on Windows CE and Mobile.pdf All Documentation 01/17/2019
Product Brief - CF10G.pdf All Product Brief 07/09/2021
Product Brief - EC25N.pdf All Product Brief 07/09/2021
Software Integration Guide - For Windows Embedded.pdf All Documentation 01/17/2019
User Guide - Laird Regulatory Utility.pdf All Documentation 01/17/2019
CONN-RN-CF10 19.3.1.3.pdf All Software 01/17/2019
CF10 19 3 1 3.zip All Software 01/17/2019

FAQ

What is the ECCN for "Summit" Wi-Fi radios?

The ECCN for the radios listed, which comprise the "Summit" line of Wi-Fi radios, is 5A002.

Do we recommend conformal coating your modules?

We highly do not recommend conformal coating the radio module. If you plan on encapsulating the radio module in a potting compound or conformal coating, you must assure that the compound in liquid or solid form does not enter under the shield where there are sensitive RF components. Some of the capacitive and inductance values are as low (pF and nH) and could be sensitive to contacting materials such as potting compounds. There are potting compounds and conformal coatings which have very good dielectric constants and are suitable for 2.4 GHz potting applications, however, when you apply any of these, they were not accounted for in the circuit design and might reduce performance of the device (or all together cause it not to function).  You should run tests on their particular potting compound and evaluate radio's performance and range.  Also, it's worth mentioning that applying any compound, conformal coating or potting directly to the module WILL void the warranty. If your application requires 100% sealing of the radio module, there is a way to do this very successfully without impacting the module performance. Simply place the module on your PCB. Place a plastic cover over the module (like a hat), make the cover large enough to cover the whole module. Apply glue around the bottom perimeter of the cover where it sits on the PCB. This allows the module to function in free air-space while there is a complete seal around it. This information is only for reference and we recommend you should conduct your own testing with your prototype of your end application to find the best suitable fit for your design.  

How many reflows do you recommend for your modules?

We only recommend reflowing our modules once as it can damage the module and void the warranty.

What's the recommended process to clean modules?

The recommended cleanser is "hydrocarbon cleaning oil", which can be used to clean the RF shield and PCB. We do not recommend the use of alcohol as it doesn't work as well and could leave residue on the boards.  

Following WPA / WPA2 authenticated failure, scu_tray will pop up a message indicating authentication failure. How do I enable/disable this feature?

You can modify this feature by creating a new registry called ?NotifyAttempts? under ?hklm/software/Laird/ScuTray?, this allows you to disable / enable the pop-up message for WPA / WPA2 authentication and even set the number of attempts before notification. -DWORD: NotifyAttempts -Values: 0 (disabled); NOT 0 (the number of attempts before notification)

Are the roam settings used to switch between profiles within the auto profile list?

Yes, here is an example. 1. The auto profile list contains SSID_1 and SSID_2 2. Device is connected to SSID_1 3. RSSI drops below roam trigger, the radio scans for other APs and finds SSID_2 is a better candidate 4. The radio disconnects from SSID_1 and connects to SSID_2

How do I troubleshoot the status information in LCM / SCU?

For the 10, 15, 30, and 40 series, the status of the LCM / SCU can be in one of two states, "non-associated? and ?associated". Once the radio has associated with an AP, it will move from "non-associated? to ?associated". If WPA / WPA2 authenticates failure, the status will switch between "non-associated? and ?associated". If authentication occurs without an IP the radio cannot be identified from the status field -- you will need to check in the IP field. For the 45 and 50 series, the status in LCM / SCU can be in one of three states, "Not Associated", "Associated", and "Connected?. Associated with no IP is a valid state for our radios to attempt to reconnect with an invalid PSK. Once the radio has associated with an AP, it will move from "not associated? to ?associated". Only after the radio authenticates and has an IP will it move to the "Connnected" state. In the case of WPA or WPA2 authenticated failure or authentication without an IP the radios will remain  in an "associated" state.

Why is the signal strength in the driver log larger than 0dBm for the CF Series?

The driver adds a weighting factor of 75 to the RSSI value for all APs that are on the preferred band and above the roam trigger. This weighting factor usually makes the RSSI positive and ensures that any APs seen on the preferred band will be used before anything on the other band (as long as they are above the roam trigger).

Can CE5 and CE6 support SHA-2?

No, the patch that supports SHA-2 is in the Windows Embedded Compact 7 Monthly Update (April 2016). Prior to that, the OS itself doesn't support it.

How do you keep the tray icon off permanently in CE/WM platform?

Setting the following registry to 0 can achieve this: HKLM\Comm\SDCCF10G1\Parms\Configs\GlobalConfig DWORD: trayIcon - 0 = Hide Icon - Non-0 = Show Icon

Before LCM detects a Wi-Fi radio, how do I hard code the radio module it would use?

The radio chipset value is written by the driver when it loads, and indicates which radio is actually installed. LCM uses this value to determine some parameters that vary between radio types. If you want to hard code the Wi-Fi radio before the driver loads, you can do so with this registry: [HKEY_LOCAL_MACHINE/Comm/SDCCF10G1/Parms/Configs/GlobalConfig] "RadioChipSet"=dword:00000006 The values for that registry key are in the sdc_sdk.h as follows: typedef enum _RADIOCHIPSET { RADIOCHIPSET_NONE = 0, RADIOCHIPSET_SDC10 = 1, //BCM4318 RADIOCHIPSET_SDC15 = 2, //BCM4322, RADIOCHIPSET_SDC30 = 3, //AR6002, RADIOCHIPSET_SDC40L = 4, //BCM4319, RADIOCHIPSET_SDC40NBT = 5, //BCM4329, RADIOCHIPSET_SDC45 = 6, //AR6003, RADIOCHIPSET_SDC50 = 7, //AR6004, } RADIOCHIPSET;

mandatory/optional input for EAP type

mandatory/optional input for EAP type   EAP credentials Mandatory input Optional input LEAP User name, user password   EAP FAST User name, user password PAC file, FAC password PEAP MSCHAP User name, user password CA cert PEAP GTC User name, user password CA cert EAP TLS User name, user cert CA cert EAP TTLS User name, user password CA cert PEAP TLS User name, user cert CA cert   Note 1: this settings should be read in user perspective but not for actual implementation. For example, when a user does not input PAC file, it will use auto PAC provisioning. If a user inputs it, it will do a manual PAC provisioning. Note 2: user password is not used for TLS but only user cert is used instead.    

 

In EAP-TLS, there is a setting of username. What is the purpose of it? Will it be used during the authentication? Does it need to be the same as in CA?

EAP-TLS is a tunnel authentication. outer identity: this is the User-Name in the RADIUS packet and visible to all intermediate parties inner identity: this is the actual user identification. It is only visible to the user himself and the Identity Provider The user cert is issued to a user identified by the username, so the username has to be configured so we know which user cert we should be using for the authentication. By default, the username is also used during authentication as the outer identity which gets sent in the identity response packet.

 

What are the reasons for the null packets in an RF trace?

There are two reasons to send out null packets with p bit enabled. 1. Its RSSI has crossed over the Roam Trigger and the client radio is supposed to start scanning for a new AP. 2. The client radio is running one of our power-save modes (Fast or Max) and is going to sleep for a brief (e.g. 20 ms) period and is telling the AP so it will buffer traffic for it while it sleeps. After a radio has slept for some period of time (defined as the interval between DTIM periods) it is supposed to wake up and indicate to the AP that it is awake by sending a null packet with the P-bit turned off. The radio should only wake if it has traffic to send or it sees from the DTIM in the AP?s beacons that the AP has traffic to send to it.

 

Does Laird recommend ways to suspend/resume for Wi-Fi radios?

Method 1: Radio driver is asked by power manager to go to low power state Suspend/resume without cutting power to radio Method 2: Radio driver is asked by power manager to go to low power state Cut power to radio Suspend/ Resume Reapply power to radio Eject/insert radio Note 1: Method 1 is the simplest way to deal with suspend/resume, but the OEM needs to consider the current consumption of the radio at a low power state. For example, current consumption for the 40NBT is 7.7mA and for the 45N it is 200uA. Note 2 : In general, method 1 is more recommended because method 2 may cause a delay to make the radio reconnect after resume.

 

What is the difference between sdcgina.exe and sdc_gina.exe?

sdcgina.exe vs sdc_gina.exe : sdcgina.exe spawns all of the components we need (e.g. supplicant, scutray). sdc_gina.exe is a UI application that, for example, pops up when the credentials must be input.

DFS channels in KCC

The following channels require DFS in Korea KCC/KC domain. Channel Frequency MHz 52 5260 56 5280 60 5300 64 5320 100 5500 104 5520 108 5540 112 5560 116 5580 120 5600 124 5620

 

What is the difference between eap-mschapv2 and mschapv2 in EAP_TTLS?

With EAP-MS-CHAPv2, the data sent in tunnel will be encapsulated as EAP-MESSAGE AVP (attribute-value pair). In the case of MS-CHAPv2, there is no such extra encapsulation it is just the MS-CHAPv2 message.

 

KCC domain

The attached document is the list current channels for the KCC domain as of 2015. In document, red means DFS required.

As the PMKcaching, two options in the setting, standard or opmk. What is the definition of these two options?

Standard: indicates PMK Caching: This means that the 802.1x authentication can be skipped on an access point that a client has already authenticated to once before. Only the 4-way handshake needs to happen. This is useful for a client that needs to reconnect to an access point that it roamed away from previously, due to signal loss etc. However, if a client has not roamed to a particular access point during its current working session, it must then authenticate to that specific access point using 802.1x. PMK Caching is the method defined in the 802.11x (WPA/WPA2) specification. Opportunistic Key Caching: With this method, a client device can skip the 802.1x authentication with an access point after a full authentication,and only needs to perform the 4 way handshake when roaming to access points that are centrally managed by the same WLC in an LWAPP or other controller-based infrastructure. This means that the client doesn't need to authenticate with access points that it wants to roam to, as long as the client has authenticated successfully to at least one of the access points in the same zone as the access point that handled the previous successful authentication. In this case, the PMK identifier has been cached at a central location, like the WLC (or wireless switch.) With OKC, the client must support this method for it to be used, even if the infrastructure has been configured with OKC enabled.

Which EAP types Laird supports in CCKM?

CCKM is supported with all EAP types Laird supports?LEAP, EAP-FAST, PEAP-MSCHAPv2, PEAP-GTC, PEAP-TLS, EAP-TLS and EAP-TTLS. ACS supports all of the EAP types except EAP-TTLS. However, supporting CCKM is not dependent on using ACS as the RADIUS server. Laird can do CCKM with any RADIUS server since CCKM support is in the wireless infrastructure.

Become a Ezurio (formerly Laird Connectivity) Customer and Gain Exclusive Access to Our Design Services Team

  • Antenna Scans
  • Antenna selection and placement
  • Custom antenna design
  • Worldwide EMC testing / certifications
  • Embedded RF hardware / firmware design
  • Cloud architecture and integration
  • Mobile application development
  • Product & Industrial Design

Talk to an Expert

Buy Now

Distributor Part In Stock Region Buy
DigiKey SDC-CF10G 73 North America Buy Now

Distributors

Distributor Phone Number Region Website
Alpha Micro UK Only +44 1256-851770
EMEA Website
Arrow Electronics 1-855-326-4757
+44 2039 365486
APAC, North America, South America, EMEA Website
Avnet 1-480-643-2000
+44 1628 512900
APAC, North America, South America, EMEA Website
Braemac Australia, New Zealand, South East Asia +61 2 9550 6600
+64 9 477 2148
APAC Website
Cal-Chip Connect 1-215-942-8900
North America Website
DigiKey 1-800-344-4539
North America, South America, APAC, EMEA Website
EBV Elektronik EMEA Website
Farlink Technology China, Hong Kong +86 13266922199
APAC Website
Farnell 1-800-936-198
+44 3447 11 11 22
EMEA Website
Future Electronics 1-800-675-1619
1-514-428-8470
North America, South America, APAC, EMEA Website
Glyn +49-6126-590-0
EMEA Website
Jetronic China, Hong Kong and Taiwan 852-27636806 
APAC Website
Laird Connectivity 1-847-839-6925
+44 1628 858941
North America, South America, APAC, EMEA Website
M2M Germany +49-6081-587386-0
EMEA Website
Martinsson +46 8 7440300
EMEA Website
McCoy South East Asia +65 6515 2988
APAC Website
Mouser 1-800-346-6873
+44 1494 427500
North America, South America, APAC, EMEA Website
RS Components +852-2421-9898
+44 3457-201201
North America, South America, APAC, EMEA Website
Ryoyo Japan +81-3-3543-7711
APAC Website
Solsta UK Only +44 (0) 1527 830800
EMEA Website
Supreme Components International India, South East Asia +65 6848-1178
APAC Website
Symmetry Electronics 1-866-506-8829
North America Website
Tekdis Australia and New Zealand +61 3 8669 1210
APAC Website
Telsys +972 3 7657666
EMEA Website
WPG +44 1628 958460
EMEA Website