ews-wifidoc-button  ews-wifisoft-button  ews-blog-button  Video Button  White Papers  ews-knowledgecenter-button  ews webinar button 


Market-Proven Dual-Band Compact Flash Module

*The CF10AG has reached end of production and is available on a limited basis only. 

The CF10AG provides all key Laird hardware and software capabilities in a Compact Flash form factor. This dual band radio module operates in both the 2.4 GHz and 5 GHz frequency bands supporting IEEE 802.11a, 802.11b, and 802.11g. As a result, the CF10AG is ideal for integration into mobile devices like handheld and vehicle mounted mobile computers, medical devices and portable printers.

Download CF10AG Hardware Integration Guide (PDF) (version 2.0, 10/23/13)
 

System Interface 16-bit Compact Flash Type I with 50-pin connector

Note: This card is not designed for operation in the CF slot on standard laptop and desktop PCs. For these devices, Laird Technologies suggests using the PC20G in the PC Card (PCMCIA) or CardBus slot found on most laptops and desktops.  
Antenna Interface 4 Hirose U.FL connectors for dual band antenna diversity
Chipset Broadcom BCM4318E
Input Power Requirements 3.3 VDC +/- 10%
Typical Power Consumption (at maximum transmit power setting)
  • Transmit:440 mA (1320mW) 
  • Receive:180 mA (594mW) 
  • Standby:10 mA (33 mW) 
 
Operating Temperature -30° to 85°C (-22° to 185°F)
Operating Humidity 10 to 90% (non-condensing)
Length 54.5 mm (2.15 in.)
Width 43 mm (1.69 in.)
Thickness 5 mm (0.2 in.)
Weight 20g (0.7 oz)
Mounting
  • 50 pin connector
  • Through Hole

    Note: Laird Technologies recommends that the mounting holes be connected to the mating circuit board with conductive screws that connect to the ground plane of the main circuit board. This is helpful in reducing radiating emissions below 1GHz that are a common occurrence in high-speed electrical circuits. 
 
Wireless Media
  • Direct Sequence-Spread Spectrum (DSSS)
  • Orthogonal Frequency Divisional Multiplexing (OFDM)
 
Media Access Protocol Carrier sense multiple access with collision avoidance (CSMA/CA)
Network Architecture Types Infrastructure and Ad Hoc
Network Standards IEEE 802.11a, 802.11b, 802.11d, 802.11e, 802.11g, 802.11h, 802.11i
Data Rates Supported
  • 802.11a (OFDM): 6, 9, 12, 18, 24, 36, 48, 54 Mbps
  • 802.11b (DSSS): 1, 2, 5.5, 11 Mbps
  • 802.11g (OFDM): 6, 9, 12, 18, 24, 36, 48, 54 Mbps
 
Modulation
  • 1, 6, 9 Mbps:BPSK 
  • 2, 12, 18 Mbps:QPSK 
  • 5.5, 11 Mbps:CCK 
  • 24, 36 Mbps:16-QAM 
  • 48, 54 Mbps:64-QAM 
 
Regulatory Domain Support
  • FCC (Americas, Parts of Asia and Middle East)
  • ETSI (Europe, Middle East, Africa and Parts of Asia)
  • MIC (formerly TELEC) (Japan)
  • KC (formerly KCC) (Korea)
 
2.4 GHz Frequency Bands
    ETSI:
  • 2.4 GHz to 2.483 GHz
    FCC:
  • 2.4 GHz to 2.473 GHz
    MIC (Japan):
  • 2.4 GHz to 2.495 GHz
    KC (Japan):
  • 2.4 GHz to 2.483 GHz
 
5 GHz Frequency Bands
    ETSI:
  • 5.15 GHz to 5.35 GHz
  • 5.47 GHz to 5.725 GHz
    FCC:
  • 5.15 GHz to 5.35 GHz
  • 5.47 GHz to 5.725 GHz
  • 5.725 GHz to 5.82 GHz
    MIC (Japan):
  • 5.15 GHz to 5.35 GHz
 
2.4 GHz Operating Channels
  • ETSI:13 (3 non-overlapping) 
  • FCC:11 (3 non-overlapping) 
  • MIC:14 (4 non-overlapping) 
 
5 GHz Operating Channels
  • ETSI: 19 non-overlapping
  • FCC: 23 non-overlapping
  • MIC: 8 non-overlapping
 
Transmit Power Settings











Maximum transmit power will vary according to individual country regulations. All values nominal, +/-2 dBm  
    802.11a:
  • 15 dBm (30 mW)
  • 10 dBm (10 mW)
  • 0 dBm (1 mW)
    802.11b:
  • 18 dBm (63 mW)
  • 17 dBm (50 mW)
  • 15 dBm (30 mW)
  • 10 dBm (10 mW)
  • 0 dBm (1 mW)
    802.11g:
  • 15 dBm (30 mW)
  • 10 dBm (10 mW)
  • 0 dBm (1 mW)
 
Typical Receiver Sensitivity
    802.11a:
  • 6 Mbps:-85 dBm 
  • 9 Mbps:-84 dBm 
  • 12 Mbps:-83 dBm 
  • 18 Mbps:-80 dBm 
  • 24 Mbps:-76 dBm 
  • 36 Mbps:-73 dBm 
  • 48 Mbps:-70 dBm 
  • 54 Mbps:-65 dBm (PER <= 10%) 
    802.11b
  • 1 Mbps:-96 dBm 
  • 2 Mbps:-95 dBm 
  • 5.5 Mbps:-94 dBm 
  • 11 Mbps:-90 dBm (PER <= 10%) 
    802.11g
  • 6 Mbps:-94 dBm 
  • 9 Mbps:-91 dBm 
  • 12 Mbps:-88 dBm 
  • 18 Mbps:-86 dBm 
  • 24 Mbps:-83 dBm 
  • 36 Mbps:-78 dBm 
  • 48 Mbps:-76 dBm 
  • 54 Mbps:-75 dBm (PER <= 10%) 
 
Delay Spread
  • 1 Mbps:600 ns 
  • 2 Mbps:500 ns 
  • 5.5 Mbps:400 ns 
  • 6 Mbps:400 ns 
  • 9 Mbps:400 ns 
  • 11 Mbps:200 ns 
  • 12 Mbps:350 ns 
  • 18 Mbps:350 ns 
  • 24 Mbps:250 ns 
  • 36 Mbps:250 ns 
  • 48 Mbps:150 ns 
  • 54 Mbps:150 ns 
 
Operating Systems Supported
  • Windows Mobile 6.0
  • Windows Mobile 5.0
  • Windows CE 6.0
  • Windows CE 5.0
  • Windows CE 4.2
  • Windows Mobile 2003
  • Windows XP Professional
  • Windows XP Embedded
 
Security
    Standards:
  • Wireless Equivalent Privacy (WEP)
  • Wi-Fi Protected Access (WPA)
  • IEEE 802.11i (WPA2)
    Encryption:
  • Wireless Equivalent Privacy (WEP, RC4 Algorithm)
  • Temporal Key Integrity Protocol (TKIP, RC4 Algorithm)
  • Advanced Encryption Standard (AES, Rijndael Algorithm)
    Encryption Key Provisioning:
  • Static (40 and 128 bit lengths)
  • Pre-Shared (PSK)
  • Dynamic
    802.1X Extensible Authentication Protocol Types:
  • EAP-FAST
  • EAP-TLS
  • EAP-TTLS
  • PEAP-GTC
  • PEAP-MSCHAPv2
  • PEAP-TLS
  • LEAP
 
Compliance  
Certifications  Wi-Fi CertifiedWi-Fi Alliance: Cisco_Compatible_35x30Cisco Compatible Extensions (Version 4)   
Warranty Limited Lifetime 

All specifications are subject to change without notice 

The CF10AG is certified for compliance to various CE, ETSI, FCC, Industry Canada, MIC, and Wi-Fi Alliance standards as well as Cisco Compatible Extensions (CCX) specifications. The grants, approvals, and formal test reports associated with these certifications may be leveraged by Laird customers to achieve their required device certifications. The degree to which customers can leverage these items is dependent upon the regulatory agency, industry body, and the type of end device.

If any additional information or guidance is required, please contact the Laird wireless certifications group via email or by telephone at 330.434.7929.


CE / ETSI

The CF10AG has been tested for compliance to various CE and ETSI standards and specifications:

This testing was conducted with the following dual band antennas:

These formal test reports may be leveraged by mobile and portable device vendors as part of their self-declaration to obtain the CE mark required by members of the European Union. ETSI/CE rules differ from those of the FCC and IC in that there is no provision for a modular approval. All approvals and certifications must exist at the device level, rather than at the radio module (radio) level.

Laird has obtained a Frequency Authority Certificate for the CF10AG and is fully compliant with Annex IV procedures in article 10.5 of R&TTE directive 99/5/EC.

Like all Laird Wi-Fi devices, the CF10AG is fully compliant with European Union Directive 2011/65/EU or Reduction of Hazardous Substances (RoHS) and Registration, Evaluation, Authorization, and Restriction of Chemicals (REACH) as per our Declaration of Compliance.

Laird 10- and 20-Series EN 300 328 v1.8.1 Updates

EN 300 328 v.1.8.1, which officially goes into effect on January 2015, includes new mandatory spectrum sharing requirements with the goal of reducing interference within the 2.4 GHz band. The following are the two main ways to achieve this: 

  • By incorporating adaptivity functionality such as DAA (Detect and Avoid), CCA (Clear Channel Assessment), and LBT (Listen Before Talk) 
  • By reducing the radio’s power, duty cycle, or both The 10-series and 20-series radios rely on the Broadcom BCM4318 chip.

Due to this, these radios have issues with the CCA aspects of spectrum sharing. Although we have received a Declaration of Compliance for the BCM4318, this is the extent of the assistance we have received from Broadcom. Despite repeated requests to Broadcom over the past 12 months, we have not received test reports that support this compliance or firmware updates to fix the CCA issues.

Given the above, our customers with these products currently have the following options: 


FCC

Laird has received the following two FCC Limited Modular Approval (LMA) grants for the CF10AG (FCC identifier TWG-SDCCF10AG):

Part 15.247 Subpart C (DTS)

This grant relates to operation in the 2.412 to 2.462 GHz (ISM) and 5.745 to 5.805 GHz (UNII-3) frequency bands.

Part 15.407 Subpart E (DFS)

This grant relates to operation in the 5.180 to 5.240 GHz (UNII-1), 5.280 to 5.320 GHz (UNII-2), and 5.500 to 5.700 GHz (UNII-2 Extended) frequency bands.

These grants were secured with the following antennas:

The above grants are Limited Modular Approvals. Specific limitations are indicated on each grant:

  • The CF10AG must be installed by an Original Equipment Manufacturer (OEM) such as a Portable Data Terminal vendor.
  • When using this grant, the CF10AG must be installed only in mobile devices (devices which typically operate at distances greater than 20cm, or 7.9 inches, from the human body). When certifying portable devices (those that typically operate at distances less than 20cm from the human body) a new grant must be secured by the device vendor.

Note: Laird test data may be leveraged by the device vendor to minimize the cost and time associated with the certification process.


Industry Canada

The CF10AG is certified to Industry Canada (IC) RSS-210 standard certification. The IC 6616A-SDCCF10AG certification is based on FCC certification testing, using the same antennas and transmit power and covering the same frequency bands. Test reports and data sheets relevant to this certification may be found in the FCC section above.


MIC (formerly TELEC)

Laird has secured the following MIC certifications:

Article 2 Item 19, Category WW (2.4GHz Channels 1-13)

Article 2 Item 19-2, Category GZ (2.4GHz Channel 14)

These certifications were secured with the following antennas:

Device vendors may leverage these certifications and the associated test report when applying for MIC certifications at the device level rather than the module (radio) level.


Wi-Fi Alliance

Laird has submitted the CF10AG to an authorized Wi-Fi Alliance test lab and as a result has received an Embedded Client Certification for the following standards: 802.11a, 802.11b, 802.11g, WPA (both personal and enterprise) and WPA2/802.11i (both personal and enterprise). For those host devices which include the CF10AG, the vendor may assert that their device incorporates a Wi-Fi Certified Embedded Client. The vendor need not be a member of the Wi-Fi Alliance to make this assertion but may not use the "Wi-Fi Certified" logo in conjunction with their device.

Device vendors who are members of the Wi-Fi Alliance may also choose to secure a Wi-Fi Alliance certification for their specific device. In this case, the vendor may not leverage the test data or certification for the Laird device. The vendor can, however, use the CF10AG test plan as a template, modifying it as necessary for the capabilities of their particular device. By leveraging Laird's "pre-approved" Wi-Fi software and test plan, the vendor has a greater assurance that their actual testing will result in an end device certification. Laird will provide consultative services to those vendors who choose to pursue a Wi-Fi Alliance certification for their Laird Wi-Fi equipped devices.


Cisco Compatible Extensions

Laird is a member of the Cisco Compatible Extensions (CCX) program and has a direct license from Cisco for intellectual property relating to the various versions of the CCX specifications. Laird has submitted the CF10AG to an authorized CCX test lab and has been found to be fully compliant with version 4 of the CCX specifications for application specific devices (ASDs). For those host devices which include the CF10AG, the vendor may assert that their device incorporates a Cisco Compatible radio module.

Click here for verification of CCX compliance for this product.

Device vendors who are members of the CCX program may also choose to secure CCX compliance for their end device. When incorporating the CF10AG into their product with the above software version, the vendor need not be a direct licensee for Cisco intellectual property. Rather, in this case the device vendor need only submit their CF10AG enabled device for CCX compliance testing to the version 4 test plan for ASDs. By leveraging Laird's "pre-approved" Wi-Fi software and by testing to the same plan, the vendor has a greater assurance that their actual testing will result in an end device compliance. Laird will provide consultative services to those vendors who choose to pursue CCX compliance for their Laird Wi-Fi equipped devices.

Location Phone Number Email

 
Americas +1-800-492-2320 WirelessInfo@lairdtech.com

Request Information Stock Locator Button Embedded Wireless Solutions Technical Support

Manufacturer Reps

but_dsmrdbut_dpdf 

 
Europe +44-1628-858-940 WirelessInfo@lairdtech.com

Request InformationStock Locator Button Embedded Wireless Solutions Technical Support 

 
Hong Kong +852-2923-0610 (Sales)
+852-2923-0609 (Support)
WirelessInfo@lairdtech.com
Wireless.support@lairdtech.com

Request InformationStock Locator Button Embedded Wireless Solutions Technical Support 

Warranty Statement

Laird Technologies warrants to the original end user customer of its products that its products are free from defects in material and workmanship. Subject to the conditions and limitations set forth below, Laird Technologies will, at its option, either repair or replace any part of its products that prove defective by reason of improper workmanship or materials. Repaired parts or replacement products will be provided by Laird Technologies on an exchange basis, and will be either new or refurbished to be functionally equivalent to new. If Laird Technologies is unable to repair or replace the product, it will refund the current value of the product at the time the warranty claim is made.

This limited warranty does not cover any damage to this product that results from improper installation, accident, abuse, misuse, natural disaster, insufficient or excessive electrical supply, abnormal mechanical or environmental conditions, or any unauthorized disassembly, repair, or modification. This limited warranty also does not apply to any product on which the original identification information has been altered, obliterated or removed, has not been handled or packaged correctly, has been sold as second-hand or has been resold.

This limited warranty covers only repair, replacement or refund for defective Laird Technologies products, as provided above. Laird Technologies is not liable for, and does not cover under warranty, any loss of data or any costs associated with determining the source of system problems or removing, servicing or installing Laird Technologies products. This warranty excludes 3rd party software, connected equipment or stored data. In the event of a claim, Laird Technologies' sole obligation shall be replacement of the hardware.

Duration

This limited warranty applies only to the original end user customer of the product. This limited warranty is non-transferable. This limited warranty is in force for the useful lifetime of the original end product into which the Laird Technologies product is installed. Useful lifetime of the original end product may vary but is not to exceed five (5) years from the original date of the end product purchase. Any repair, component replacement or modification to the original product constitutes the end of the lifetime of the end product as defined here.

Eligibility

Warranty on Laird Technologies products are only applicable if the parts were purchased from Laird Technologies authorized OEMs/distributors/resellers or directly from Laird Technologies.

Limitations

The following parts are not covered by this warranty:

  • Products without the label containing Laird Technologies' serial number or MAC address
  • Products that are purchased from other end users
  • Products that Laird Technologies determines were not purchased through Laird Technologies authorized OEMs/distributors/resellers or directly from Laird Technologies
  • All EOL claims to return back to point of purchase or respective distributors.

Disclaimer

The foregoing is the complete warranty for Laird Technologies products and supersedes all other warranties and representations, whether oral or written. Except as expressly set forth above, no other warranties are made with respect to Laird Technologies products and Laird Technologies expressly disclaims all warranties not stated herein, including, to the extent permitted by applicable law, any warranty that may exist under national, state, provincial or local law including but not limited to any implied warranty of non-infringement, merchantability or fitness for a particular purpose. All warranties, whether express or implied, are limited to the periods of time set forth above. 

Laird Technologies products are not authorized for use as critical components in life support equipment or for applications in which the failure or malfunction of the products would create a situation in which personal injury or death is likely to occur. Laird Technologies shall not be liable for the death of any person or any loss, injury or damage to persons or property by use of Laird Technologies products.

Laird Technologies' total liability under this or any other warranty, express or implied, is limited to repair, replacement or refund. Repair, replacement or refund are the sole and exclusive remedies for breach of warranty or any other legal theory. To the fullest extent permitted by applicable law, Laird Technologies shall not be liable to the purchaser or end user customer of a Laird Technologies product for any damages, expenses, lost data, lost revenues, lost savings, lost profits, or any other incidental or consequential damages arising from the purchase, use or inability to use the Laird Technologies product, even if Laird Technologies has been advised of the possibility of such damages.